Concrete mix ratio

The classic answer is 1 part cement, 2 parts sand and 3 parts gravel. That rule of thumb works for small, non-structural jobs. For a footing or slab, a mix by weight and a strength class you can order is the safer way to think about it.

Updated October 23, 2026 · by Dmytro Antoniuk

What 1:2:3 means

A mix ratio lists cement, sand and gravel in that order. 1:2:3 means one bucket of cement, two of sand and three of gravel. 1:2:4 is a leaner version with more gravel. Water is added until the mix is workable.

These ratios are old rules of thumb. They are measured by volume, so a fluffy bucket of sand and a packed one give different concrete. No building code we know of sets a footing strength by bucket count. Use them for fence posts, pads and repairs, not for the foundation of a house.

Mixes by weight, per strength class

Ready-mix plants batch by weight against a target strength. The calculator does the same with a nominal recipe for each class. These figures come from trade sources and are a starting point, not a mix design.

Per cubic yard

Class Cement 94 lb sacks to buy Sand (loose) Gravel (loose) Water
2,500 psi 506 lb 6 12.1 ft³ 20.7 ft³ 36.5 gal
3,000 psi 556 lb 6 11.8 ft³ 20.7 ft³ 36.5 gal
3,500 to 4,000 psi 640 lb 7 11.5 ft³ 20.3 ft³ 38.3 gal

Per cubic meter

Class Cement Sand Gravel Water
C16/20 300 kg 720 kg 1,150 kg 180 L
C20/25 330 kg 700 kg 1,150 kg 180 L
C25/30 380 kg 680 kg 1,130 kg 190 L

As ratios by weight, these work out to about 1 : 2.4 : 3.8 for the weakest class, 1 : 2.1 : 3.5 for the middle one and 1 : 1.8 : 3.0 for the strongest. More cement and less sand per yard is what buys the extra strength.

The calculator uses one recipe for both 3,500 and 4,000 psi. A site mix cannot promise the difference between them, so if your plans say 4,000 psi, order it from a plant that will certify the strength.

Water is the part that matters most

Strength depends mostly on how much water there is for each pound of cement. In the table above, the water to cement ratio is about 0.60 for the weakest class, 0.55 for the middle one and 0.50 for the strongest.

Every extra bucket of water makes the mix easier to pour and weaker once it hardens. If a batch is too stiff, add cement and water together so the ratio stays put. Wet sand already carries water, so hold some back when your sand pile is damp.

Why footings get ready-mix

Take the 40 by 30 ft house footing from the strip foundation guide. It needs 4.66 cubic yards with waste. As a 3,000 psi site mix that is:

Material Amount
Portland cement 2,589 lb, or 28 sacks of 94 lb
Sand about 55 ft³
Gravel about 96 ft³
Water about 169 gal

That is dozens of mixer loads. Each one has to match the last, and the whole trench should be filled before the first batch starts to set. It makes for a long, wet day. A ready-mix truck brings the same volume in one consistent pour, at a strength the plant stands behind, which is why footings and slabs under a house are almost always poured from a truck.

Mixing a small batch by hand

For a post, a step or a small pad, mixing yourself is fine. A 2 ft³ batch at the 3,000 psi recipe takes about 41 lb of cement (a little under half a sack), 0.9 ft³ of sand, 1.5 ft³ of gravel and 2.6 gallons of water.

  1. Measure dry materials into a wheelbarrow or mixing tub: gravel first, then sand, then cement.
  2. Mix dry with a hoe until the color is even.
  3. Add about three quarters of the water and mix, then add the rest a little at a time.
  4. Stop when it holds its shape in a ridge and does not slump flat or crumble.
  5. Place it right away. Compact it with a rod or by tapping the forms, and keep it damp while it cures.

Bagged premix skips the measuring: the bag already holds cement, sand and gravel. The concrete calculator gives both the premix bag count and the site mix for any volume.

Start with the volume

Work out the volume first with the concrete calculator, or with the foundation calculators linked from the slab foundation and strip foundation guides. Then decide between bags, a site mix and a truck.

The recipes on this page are nominal values for planning. Strength for structural work comes from a tested mix design and the class your plans or local code specify.

Concrete volume

Units
Shape and size
ft
ft
in
Waste and ordering
%

5 to 10 % covers spillage and uneven digs.

Concrete to order1.30 yd³0.991 m³

Net volume1.23 yd³ 0.944 m³
Waste added5 %
Premix bags59 × 80 lb
Assumptions behind this result
  • Nominal dimensions as entered, no over-dig or spillage beyond the waste factor.
  • Waste allowance 5 % added to the net volume (typical 5 to 10 %, footings 10 to 15 %).
  • Premix yield 0.0170 m³ per 80lb bag (Quikrete premix yield 0.60 ft³ per 80 lb bag).

Estimate only. Quantities and checks are based on the dimensions and assumptions shown. This is not structural design and not a substitute for a geotechnical report or a licensed engineer. Confirm soil capacity, loads, frost depth and local code before you build or order.

Common questions

What is the mix ratio for concrete?

The traditional rule of thumb is 1:2:3, one part cement to two parts sand to three parts gravel, with enough water to make it workable. It is a habit of the trade, not a value from a building code.

What is the concrete mix ratio for a foundation?

For footings and slabs, order ready-mix at the strength your plans or local code call for. If you must mix on site, a nominal 3,000 psi recipe is about 556 lb of cement, 11.8 ft³ of sand, 20.7 ft³ of gravel and 36.5 gallons of water per cubic yard.

What is the mix ratio for 4000 psi concrete?

By weight, roughly 1 part cement to 1.8 parts sand to 3 parts gravel with a water to cement ratio near 0.50. Hitting 4,000 psi reliably needs a tested mix design, so order it from a ready-mix plant.

How many bags of cement are in a yard of concrete?

About 6 sacks of 94 lb portland cement for a nominal 3,000 psi mix, and about 7 for 3,500 to 4,000 psi. Premix bags are different: they already contain sand and gravel.

Sources

  1. Quikrete, concrete project calculators and bag yields
  2. Panorama Firm, what concrete is made of and how proportions change it (trade source)
  3. Muratordom, B20 concrete proportions for a DIY batch (trade source)